View XQ-D_9079507.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

cld-ds52 rev 3f cree ? xlamp ? XQ-D led product description cree xlamp ? XQ-D l e ds revolutionize low-cost, high-power le ds by delivering lighting-class reliability and a wider spread of light than typical plastic packages. the xq - ds innovative wide light emission can improve the omnidirectionality of replacement lamps, while also reducing system cost by using fewer l eds. using crees newest generation of silicon carbide-based l e d chips, XQ-D is optimized to dramatically lower system cost in replacement lamp, non-directional and outdoor area lighting applications. features ? crees smallest lighting class l ed: 1.6 x 1.6 x 1.6?mm ? available in white, 80-minimum cri white, and 70-minimum cri cool white ? binned at 25?c ? 700?ma maximum drive current ? low thermal resistance: 7.5?c/w ? wide viewing angle: 145 ? refow solderable - jedec j-std-020c compatible ? unlimited foor life at 30?c/85% rh ? rohs and reach compliant ? ul ? recognized component (e349212) t able of c ontents characteristics ....................................... 2 flux characteristics ............................... 3 relative spectral power distribution .... 4 relative flux vs. junction temperature ........................................... 4 e lectrical characteristics ....................... 5 relative flux vs. current ........................ 5 typical spatial distribution .................... 6 thermal design ...................................... 6 refow soldering characteristics .......... 7 notes ...................................................... 8 mechanical dimensions ...................... 10 tape and reel ....................................... 11 packaging ............................................. 12 product family data sheet copyright ? 2013-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. cree, inc. 4600 silicon drive durham, nc 27703 usa tel: +1.919.313.5300 www. cr ee. c om/x lamp
2 ch aracteristics characteristics unit minimum typical maximum thermal resistance, junction to solder point c/w 7.5 viewing angle (fwhm) degrees 145 temperature coeffcient of voltage mv/c -3 esd classifcation (hbm per mil-std-883d) class 1 dc forward current ma 350 700 reverse voltage v -5 forward voltage (@?350?ma, 25?c) v 3.1 3.5 le d junction temperature c 150 2 copyright ? 2013-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? XQ-D led
3 f lux ch aracteristics (t j ?=?25?c) the following table provides several base order codes for xlamp XQ-D l e ds. it is important to note that the base order codes listed here are a subset of the total available order codes for the product family. for more order codes, as well as a complete description of the order- code nomenclature, please consult the xlamp xq l e d family binning and labeling document. color cct range minimum luminous flux @ 350?ma calculated minimum luminous flux (lm)* order code min. max. group flux (lm) 700 ma cool ite 5000 k 8300 k 6 130 227 5(80 r3 122 213 5(80* r2 5(80 70 cri minimum ssplmxi 5000 k 8300 k 6 130 227 5(8 r3 122 213 5(8* r2 5(8 2ixvep lmxi 3700 k 5000 k r3 122 213 5(8* r2 5(8 q5 107 187 5(80( 80 cri minimum lmxi 2600 k 5 100 172 5(8, q3 5(8, q2 153 5(8, evq lmxi 2600 k 3700 k 5 100 172 5(80 q3 5(80 q2 153 5(80 notes: u vii qemrxemr e xspiveri s r sr er tsiv qieviqirx r sr lvsqexmmx qieviqirx er r sr 6- qieviqirx 7iixli 1ieviqirxixmsrteki u 8tmep 6-sv 2ixveplmxi 8 m u 8tmep 6-sv evqlmxi 8 m u 1mrmqq6-sv6-1mrmqqssplmxim u 1mrmqq6-sv6-1mrmqqlmxim * eppexi epiexeq evisv viiviri srp copyright ? 2013-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? XQ-D led
4 r elative s pectral po wer distrib ution r elative f lux vs . j unction t emperature (i f ddd m relative spectral power 0% 20% 40% 60% 80% 100% 380 430 480 530 580 630 680 730 780 relative radiant power (%) wavelength (nm) cool white neutral white warm white relative flux output vs. junction temperature 0% 20% 40% 60% 80% 100% 120% 25 50 75 100 125 150 relative luminous flux junction temperature (oc) 4 copyright ? 2013-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? XQ-D led
5 e lectrical ch aracteristics (t j ?=?25?c) r elative f lux vs . c urrent (t j ?=?25?c) electrical characteristics (tj = 85oc) 0 100 200 300 400 500 600 700 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 forward current (ma) forward voltage (v) relative intensity vs. current (tj = 85oc) 0% 20% 40% 60% 80% 100% 120% 140% 160% 180% 0 100 200 300 400 500 600 700 relative luminous flux (%) forward current (ma) 5 copyright ? 2013-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? XQ-D led
6 ty pical s patial distribution th ermal design the maximum forward current is determined by the thermal resistance between the led junction and ambient. it is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. typical spatial radiation pattern 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% -90 -70 -50 -30 -10 10 30 50 70 90 relative luminous intensity (%) angle (o) thermal design 0 100 200 300 400 500 600 700 800 0 20 40 60 80 100 120 140 160 maximum current (ma) ambient temperature (oc) rj-a = 10c/w rj-a = 15c/w rj-a = 20c/w rj-a = 25c/w 6 copyright ? 2013-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? XQ-D led
7 7 r eflo w s oldering ch aracteristics in testing, cree has found xlamp XQ-D leds to be compatible with jedec j-std-020c, using the parameters listed below. as a general guideline, cree recommends that users follow the recommended soldering profle provided by the manufacturer of the solder paste used. note that this general guideline may not apply to all pcb designs and confgurations of refow soldering equipment. profile feature lead-free solder average ramp-up rate (ts max to tp) 1.2?c/second preheat: temperature min (ts min ) 120 c preheat: temperature max (ts max ) 170 c preheat: time (ts min to ts max ) 65-150 seconds time maintained above: temperature (t l ) 217 c time maintained above: time (t l ) 45-90 seconds peak/classifcation temperature (tp) 235 - 245 c time within 5?c of actual peak temperature (tp) 20-40 seconds ramp-down rate 1 - 6 c/second time 25?c to peak temperature 4 minutes max. note: all temperatures refer to topside of the package, measured on the package body surface. ipc/jedec j-std-020c t p t l temperature time t 25?c to peak preheat ts t s t p 25 ramp-down ramp-up critical zone t l to t p ts max ts min copyright ? 2013-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? XQ-D led
8 8 n otes measurements the luminous fux, radiant power, chromaticity and cri measurements in this document are binning specifcations only and solely represent product measurements as of the date of shipment. these measurements will change over time based on a number of factors that are not within crees control and are not intended or provided as operational specifcations for the products. calculated values are provided for informational purposes only and are not intended as specifcations. pre?release qualifcation testing please read the le d reliability overview for details of the qualifcation process cree applies to ensure long-term reliability for xlamp leds and details of crees pre-release qualifcation testing for xlamp leds. lumen maintenance cree now uses standardized ies lm-80-08 and tm-21-11 methods for collecting long-term data and extrapolating led lumen maintenance. for information on the specifc lm-80 data sets available for this led, refer to the public lm-80 results document . please read the long-term lumen maintenance application note for more details on crees lumen maintenance testing and forecasting. please read the thermal management application note for details on how thermal design, ambient temperature, and drive current affect the le d junction temperature. moisture sensitivity cree recommends keeping xlamp leds in the provided, resealable moisture-barrier packaging (mbp) until immediately prior to soldering. unopened mbps that contain xlamp le ds do not need special storage for moisture sensitivity. once the mbp is opened, xlamp XQ-D leds may be stored as msl 1 per jedec j-std-033, meaning they have unlimited foor life in conditions of 30 oc/85% relative humidity (rh). regardless of storage condition, cree recommends sealing any unsoldered leds in the original mbp. rohs compliance the levels of rohs restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with eu directive 2011/65/ec (rohs2), as implemented january 2, 2013. rohs declarations for this product can be obtained from your cree representative or from the product documentation sections of www.cree.com . reach compliance reach substances of very high concern (svhcs) information is available for this product. since the european chemical agency (echa) has published notice of their intent to frequently revise the svhc listing for the foreseeable future, please contact a cree representative to insure you get the most up-to-date reach svhc declaration. reach banned substance information (reach article 67) is also available upon request. copyright ? 2013-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? XQ-D led
9 ul ? recognized component level 1 enclosure consideration. the led package or a portion thereof has not been investigated as a fre enclosure or a fre and electrical enclosure per ansi/ul 8750. v ision advisory warning: do not look at an exposed lamp in operation. eye injury can result. for more information about leds and eye safety, please refer to the led e ye safety application note . n otes - c ontinued copyright ? 2013-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? XQ-D led
10 mech anical dimensions all dimensions in mm. measurement tolerances unless indicated otherwise: .13 mm size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 1.60 1.60 1.41 .600 .600 .300 1.500 1.60 .05 .30 1.60 .65 1.60 .300 1.500 3.300 3.300 1 / 1 45.000 a 2610-00026 xqx outline -- -- -- -- -- -- 5/23/12 d. cronin revisons rev description by date app'd recommended pc board solder pad recommended trace layout solder pad reference notch is on cathode (-) side size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 1.60 1.60 1.41 .600 .600 .300 1.500 1.60 .05 .30 1.60 .65 1.60 .300 1.500 3.300 3.300 1 / 1 45.000 a 2610-00026 xqx outline -- -- -- -- -- -- 5/23/12 d. cronin revisons rev description by date app'd recommended pc board solder pad recommended trace layout solder pad reference notch is on cathode (-) side size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 1.60 1.60 1.41 .600 .600 .300 1.500 1.60 .05 .30 1.60 .65 1.60 .300 1.500 3.300 3.300 1 / 1 45.000 a 2610-00026 xqx outline -- -- -- -- -- -- 5/23/12 d. cronin revisons rev description by date app'd recommended pc board solder pad recommended trace layout solder pad reference notch is on cathode (-) side top view side view b ottom view .30 1.60 .65 1.60 .300 1.500 3.300 3.300 1.60 1.60 1.58 .08 1.500 .600 .600 .300 r .936 .375 recommended pc board solder pad recommended trace layout solder pad reference notch is on cathode(-) side .30 1.60 .65 1.60 .300 1.500 3.300 3.300 1.60 1.60 1.58 .08 1.500 .600 .600 .300 r .936 .375 recommended pc board solder pad recommended trace layout solder pad reference notch is on cathode(-) side recommended trace layout recommended pcb solder pad 10 copyright ? 2013-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? XQ-D led
11 11 t ape and reel all cree carrier tapes conform to eia-481d, automated component handling systems standard. except as noted, all dimensions in mm. measurement tolerances unless indicated otherwise: .xx = .25 mm, .xxx = .125 mm size title of rev. sheet c drawing no. date date date check final protective finish material approved drawn by third angle projection scale a b c d 1 2 3 4 5 6 6 5 4 3 2 1 a b c d phone (919) 313-5300 fax (919) 313-5558 4600 silicon drive durham, n.c 27703 unauthorized person without the written consent may not be copied, reproduced or disclosed to any confidential information of cree, inc. this plot contained within are the proprietary and cree confidential. this plot and the information of cree inc. notice x .5 .xxx .25 .xx .75 .x 1.5 for sheet metal parts only .xx .25 .xxx .125 x .5 unless otherwise specified dimensions are in millimeters and after finish. tolerance unless specified: surface finish: 1.6 a a .30 .10 3.50 .10 1.85 1.65 1.750 8.000 nominal 8.30 max 1.000 +.10 -.00 1.500 4.000 2.000 revisons rev description by date app'd 1 / 1 4.000 a 2402-00023 carrier tape, 1.7x1.7 xpq 5/31/12 d. cronin notes: 1. 10 sprocket hole pitch cumulative tolerance 0.2mm reference vendor part number 021142 cathode side anode side loaded pockets (2,000 lamps) leader 400 mm (min) of empty pockets with at least 100 mm sealed by tape (50 empty pockets min.) trailer 160 mm (min) of empty pockets sealed with tape (20 pockets min.) start end cathode side anode side (denoted by + and circle) 2.5 .1 1.5 .1 8.0 .1 4.0 .1 1.75 .10 12.0 .0 + .3 13 mm 7" cover tape pocket tape user feed direction user feed direction copyright ? 2013-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? XQ-D led
12 12 patent label (on bottom of box) label with cree bin code, quantity, reel id label with cree bin code, quantity, reel id label with cree order code, quantity, reel id, po # label with cree order code, quantity, reel id, po # label with cree bin code, quantity, reel id unpackaged reel packaged reel boxed reel cree bin code & barcode label vacuum-sealed moisture barrier bag label with customer p/n, qty, lot #, po # label with cree bin code, q t y , lot # label with cree bin code, q t y , lot # v acuum - sealed moisture barrier bag p atent label label with customer order code, q t y , r eel i d , po # p ac k aging the diagrams below show the packaging and labels cree uses to ship xlamp XQ-D l e ds. xlamp XQ-D le ds are shipped in tape loaded on a reel. each box contains only one reel in a moisture barrier bag. copyright ? 2013-2016 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree ? and xlamp ? are registered trademarks and the cree logo is a trademark of cree, inc. ul ? and the ur logo are registered trademarks of ul llc. xlamp ? XQ-D led

▲Up To Search▲

Price & Availability of XQ-D

	To Download XQ-D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .